Cause of drive axle fracture
![](/skin/Gold/line_sep1.gif)
摘 要
某型号拖拉机的驱动轮轴在感应淬火后的校直工序中发生断裂,采用宏观观察、金相检验、热酸蚀试验等方法对断裂原因进行分析。结果表明:驱动轮轴在锻造过程中产生了局部过烧,导致材料的强度和塑性大大降低,当受到过大的外部作用力时,零件发生了断裂。
![](flash/relate.gif)
![](flash/relate.gif)
![](flash/relate.gif)
![](flash/relate.gif)
![](flash/relate.gif)
![](flash/relate.gif)
![](flash/relate.gif)
![](flash/relate.gif)
Abstract
The drive axle of a certain type of tractor fractured in the straightening process after induction quenching. The fracture cause was analyzed by means of macroscopic observation, metallographic examination and hot acid etching test. The results show that the local overburning of the drive axle during the forging process led to a significant reduction in the strength and plasticity of the material. When the external force was too large, the part broke.
中图分类号 TB31 TG115.2 DOI 10.11973/lhjy-wl202304008
所属栏目 质量控制与失效分析
基金项目
收稿日期 2022/5/10
修改稿日期
网络出版日期
![](/skin/blank.gif)
作者单位点击查看
![](/skin/blank.gif)
备注魏彩丽(1986-),女,硕士,工程师,主要从事理化检验与失效分析工作,547452328@qq.com
引用该论文: WEI Caili,ZHANG Shenjie,DU Gangfeng,LI Peizhe. Cause of drive axle fracture[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2023, 59(4): 29~30
魏彩丽,张沈洁,杜冈峰,李佩哲. 驱动轮轴断裂原因[J]. 理化检验-物理分册, 2023, 59(4): 29~30
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
![请选择您对本文的评价](/skin/Gold/evaluation/ev_01.gif)
![您认为本文一无是处!](/skin/Gold/evaluation/ev_02.gif)
![您认为本文较差,没啥用!](/skin/Gold/evaluation/ev_03.gif)
![您认为本文一般,没太大参考价值](/skin/Gold/evaluation/ev_04.gif)
![您认为本文尚可,值得参考](/skin/Gold/evaluation/ev_05.gif)
![您认为本文很好,值得推荐](/skin/Gold/evaluation/ev_06.gif)
参考文献
【1】冶金工业部钢铁研究院.合金钢断口分析金相图谱[M].北京:科学技术出版社,1979.
【2】王广生,石康才,周敬恩.金属热处理缺陷分析及案例[M].北京:机械工业出版社,2007.
【3】崔广磊,李超,阎平.34CrNiMo6钢过热过烧断口研究[J].包头职业技术学院学报,2021,22(3):32-35.
【4】林治明.关于钢过热过烧断口的新观察[J].理化检验(物理分册),1981,17(5):2-7.
【5】高东宏,张炜.超声波探伤技术在转向节过热过烧缺陷检测中的应用[J].汽车工艺与材料,2020(8):18-23.
【2】王广生,石康才,周敬恩.金属热处理缺陷分析及案例[M].北京:机械工业出版社,2007.
【3】崔广磊,李超,阎平.34CrNiMo6钢过热过烧断口研究[J].包头职业技术学院学报,2021,22(3):32-35.
【4】林治明.关于钢过热过烧断口的新观察[J].理化检验(物理分册),1981,17(5):2-7.
【5】高东宏,张炜.超声波探伤技术在转向节过热过烧缺陷检测中的应用[J].汽车工艺与材料,2020(8):18-23.
相关信息