Effect of Semi-solid Stirring on Microstructure of Mg-6Gd-3Y-0.4Zr-2Zn Magnesium Alloy
![](/skin/Gold/line_sep1.gif)
摘 要
首先采用差热分析确定了Mg-6Gd-3Y-0.4Zr-2Zn镁合金的固相点和液相点, 然后在610.5~642.5 ℃温度区间对其进行半固态搅拌, 研究了半固态搅拌对其显微组织的影响, 并与未经半固态搅拌制备相同成分镁合金的组织进行了对比。结果表明: 半固态搅拌处理镁合金的铸态组织相对未半固态搅拌处理的而言, 晶粒尺寸有所减小, 且较圆整均匀, 第二相的连续网状结构有向断网状转变的趋势。
![](flash/relate.gif)
![](flash/relate.gif)
![](flash/relate.gif)
![](flash/relate.gif)
![](flash/relate.gif)
![](flash/relate.gif)
![](flash/relate.gif)
![](flash/relate.gif)
Abstract
Liquidus and solidus temperature of Mg-6Gd-3Y-0.4Zr-2Zn magnesium alloy were determined by means of differential thermal analysis, and semi-solid stirring was carried out at 610.5-642.5 ℃. The effect of semi-solid stirring on microstructure of the magnesium alloy was studied, and compared with the microstructure of the magnesium alloy without semi-solid stirring. The results show that, comparing with the microstructure of the magnesium alloy without semi-solid stirring, the grain size of the alloy with semi-solid stirring gets refined and spheroidized, meanwhile, the continuous network structure of second phases had a tendency to discontinuousness.
中图分类号 TG146.2
所属栏目 试验研究
基金项目 国家“973”重点基础研究项目(2013CB632200)
收稿日期 2013/5/27
修改稿日期 2014/4/3
网络出版日期
![](/skin/blank.gif)
作者单位点击查看
![](/skin/blank.gif)
备注薛寒松(1968-), 男, 江苏南京人, 副教授, 博士。
引用该论文: XUE Han-song,PENG Kai-jian,WU Zhao-bing,XIANG Jun-jun,ZHANG Ding-fei. Effect of Semi-solid Stirring on Microstructure of Mg-6Gd-3Y-0.4Zr-2Zn Magnesium Alloy[J]. Materials for mechancial engineering, 2014, 38(5): 17~20
薛寒松,彭开建,吴招兵,向军军,张丁非. 半固态搅拌对Mg-6Gd-3Y-0.4Zr-2Zn镁合金显微组织的影响[J]. 机械工程材料, 2014, 38(5): 17~20
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
![请选择您对本文的评价](/skin/Gold/evaluation/ev_01.gif)
![您认为本文一无是处!](/skin/Gold/evaluation/ev_02.gif)
![您认为本文较差,没啥用!](/skin/Gold/evaluation/ev_03.gif)
![您认为本文一般,没太大参考价值](/skin/Gold/evaluation/ev_04.gif)
![您认为本文尚可,值得参考](/skin/Gold/evaluation/ev_05.gif)
![您认为本文很好,值得推荐](/skin/Gold/evaluation/ev_06.gif)
参考文献
【1】罗守靖,姜永正,李远发.重新认识“半固态金属加工技术”[J].特种铸造与有色合金,2012,32(7):603-607.
【2】BUSTOS O, ORDONEZ S, COLAS R. Rheolgical and microstructural study Of A356 alloy solidified under magnetic sti-rring[J].International Journal of Metalcasting,2013,7:29-37.
【3】康永林,张帆, 周冰,等.铝、镁合金流变压铸成形技术及应用[J].有色金属科学与工程, 2011, 2(6): 1-6.
【4】陈平国, 周平瑞, 闫洪,等. SIMA法处理AZ61热、冷压形变及半固态等温组织的比较研究[J].塑性工程学报, 2008, 15(1): 112-117.
【5】甑子胜, 毛卫民, 陈洪涛,等.电磁搅拌下半固态AZ91D镁合金组织的形成[J].特种铸造及有色合金, 2005,25(3):161-163.
【6】KOOREN Z, ROSENSON H, GUTMAN EM, et al. Deve-lopment of semisolid casting for AZ91 and AM50 magnesium alloys[J].Journal of Light Metals, 2002, 2: 81-87.
【7】胡勇, 饶丽.机械搅拌法制备半固态镁合金的研究[J].金属铸锻焊技术, 2011, 23(3): 25-27.
【8】胡汉起.金属凝固原理[M].北京: 机械工业出版社, 2000.
【9】李卫民, 陈静.浇注温度和冷却速度对半固态挤压铸造AZ80镁合金组织的影响[J].铸造技术, 2012, 33(11): 1319-1320.
【10】龚晓叁, 吴有伍.镁合金AM60半固态成形性研究[J].厦门理工学院学报, 2012,20(4): 28-32.
【11】姚志英.AZ31B镁合金半固态挤压试验研究[J].热加工工艺, 2012.41(23): 52-57.
【12】林琳.单螺旋机械搅拌半固态浆料制备技术研究[D].昆明: 昆明理工大学, 2011: 25-37.
【13】徐跃, 康永林, 王朝晖.机械搅拌法制备半固态镁合金的组织及性能研究[D].北京: 北京科技大学, 2004: 31-35.
【14】闫洪, 张发云, 揭小平,等.AZ61镁合金在形变诱导法中的组织演变[J].中国机械工程, 2005, 16(8): 719-723.
【15】尚淑珍, 路贵民, 赵祖欣.6061铝合金半固态坏料部分重熔过程中的组织演变[J].机械工程材料 2010, 34(2): 1-3.
【16】JIANG J F, WANG Y, DU Z M.Microstructure and properties of AZ80 alloy semisolid billets fabricated by new strain induced melt activated method[J].Transactions of Nonferrous Metals Society of China.2012, 22: 422-427.
【2】BUSTOS O, ORDONEZ S, COLAS R. Rheolgical and microstructural study Of A356 alloy solidified under magnetic sti-rring[J].International Journal of Metalcasting,2013,7:29-37.
【3】康永林,张帆, 周冰,等.铝、镁合金流变压铸成形技术及应用[J].有色金属科学与工程, 2011, 2(6): 1-6.
【4】陈平国, 周平瑞, 闫洪,等. SIMA法处理AZ61热、冷压形变及半固态等温组织的比较研究[J].塑性工程学报, 2008, 15(1): 112-117.
【5】甑子胜, 毛卫民, 陈洪涛,等.电磁搅拌下半固态AZ91D镁合金组织的形成[J].特种铸造及有色合金, 2005,25(3):161-163.
【6】KOOREN Z, ROSENSON H, GUTMAN EM, et al. Deve-lopment of semisolid casting for AZ91 and AM50 magnesium alloys[J].Journal of Light Metals, 2002, 2: 81-87.
【7】胡勇, 饶丽.机械搅拌法制备半固态镁合金的研究[J].金属铸锻焊技术, 2011, 23(3): 25-27.
【8】胡汉起.金属凝固原理[M].北京: 机械工业出版社, 2000.
【9】李卫民, 陈静.浇注温度和冷却速度对半固态挤压铸造AZ80镁合金组织的影响[J].铸造技术, 2012, 33(11): 1319-1320.
【10】龚晓叁, 吴有伍.镁合金AM60半固态成形性研究[J].厦门理工学院学报, 2012,20(4): 28-32.
【11】姚志英.AZ31B镁合金半固态挤压试验研究[J].热加工工艺, 2012.41(23): 52-57.
【12】林琳.单螺旋机械搅拌半固态浆料制备技术研究[D].昆明: 昆明理工大学, 2011: 25-37.
【13】徐跃, 康永林, 王朝晖.机械搅拌法制备半固态镁合金的组织及性能研究[D].北京: 北京科技大学, 2004: 31-35.
【14】闫洪, 张发云, 揭小平,等.AZ61镁合金在形变诱导法中的组织演变[J].中国机械工程, 2005, 16(8): 719-723.
【15】尚淑珍, 路贵民, 赵祖欣.6061铝合金半固态坏料部分重熔过程中的组织演变[J].机械工程材料 2010, 34(2): 1-3.
【16】JIANG J F, WANG Y, DU Z M.Microstructure and properties of AZ80 alloy semisolid billets fabricated by new strain induced melt activated method[J].Transactions of Nonferrous Metals Society of China.2012, 22: 422-427.
相关信息