扫一扫 加微信
首页 > 期刊论文 > 论文摘要
废胶粉/塑料共混物的研究进展
          
Research Progress in Waste Rubber Powder/Plastic Blends

摘    要
介绍了废胶粉(WRP)与塑料共混制备热塑性弹性体/复合材料的研究进展; 重点阐述了WRP的种类、粒径、含量以及界面增容方法对WRP/塑料共混物力学性能的影响规律, 指出提高WRP与基体间的界面相容性是制备具有优异性能共混物的关键; 最后, 针对WRP在塑料共混应用中存在的问题提出了今后的研究方向。
标    签 废胶粉   塑料   共混物   界面相容性   力学性能   waste rubber powder (WRP)   plastic   blend   interface compatibility   mechanical property  
 
Abstract
The development of waste rubber powder (WRP)/plastic blends is reviewed. The influences of species, particle size and content of the WRP as well as method of interface compatibilization on the mechanical properties of the WRP/plastic blends are introduced as key points. It is pointed out that enhancing the interface compatibility between WRP and substrate is the key of fabricating WRP/plastic blends with excellent performance. Finally, new directions for future research are proposed based on the problems in WRP/plastic blends.

中图分类号 TQ320.9

 
  中国光学期刊网论文下载说明


所属栏目 综述

基金项目 安徽高校省级自然科学研究项目(KJ2013Z067); 安徽理工大学青年教师科学研究基金资助项目(QN201116); 安徽理工大学博士启动基金资助项目(2010-11060)

收稿日期 2013/1/22

修改稿日期 2013/12/1

网络出版日期

作者单位点击查看

备注杨继年(1981-), 男, 江苏东台人, 讲师, 博士。

引用该论文: YANG Ji-nian,ZHU Jin-bo,DING Guo-xin,MENG Cui-ping. Research Progress in Waste Rubber Powder/Plastic Blends[J]. Materials for mechancial engineering, 2014, 38(2): 1~5
杨继年,朱金波,丁国新,孟翠平. 废胶粉/塑料共混物的研究进展[J]. 机械工程材料, 2014, 38(2): 1~5


论文评价
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
分享论文
分享到新浪微博 分享到腾讯微博 分享到人人网 分享到 Google Reader 分享到百度搜藏分享到Twitter

参考文献
【1】LI S Y, LAMMINMKI J, HANHI K. Improvement of mechanical properties of rubber compounds using waste rubber/virgin rubber[J].Polymer Engineering & Science,2005,45(9):1239-1246.
 
【2】CHIU C T, LU L C. A laboratory study on stone matrix asphalt using ground tire rubber[J].Construction and Building Materials,2007,21(5):1027-1033.
 
【3】LIU H, MEAD J L, STACER R G. Thermoplastic elastomers and rubber-toughened plastics from recycled rubber and plastics[J].Rubber Chemistry and Technology,2002,75(1):49-63.
 
【4】李岩,张勇,张隐西.废橡胶胶粉/塑料共混物研究现状[J].中国塑料,2002,16(3):67-70.
 
【5】瓮子良,冯予星,伍社毛,等.废胶粉/高密度聚乙烯热塑性弹性体的结构与性能[J].特种橡胶制品,2006,27(5):5-9.
 
【6】吕智超,张宏雷,张勇,等.热剪切对聚乙烯/胶粉共混物结构演变及性能的影响[J].合成橡胶工业,2012,35(2):128-132.
 
【7】SONNIER R, LEROY E, CLERC L, et al. Polyethylene/ground tyre rubber blends: influence of particle morphology and oxidation on mechanical properties[J].Polymer Testing,2007,26(2):274-281.
 
【8】OUYANG C F, GAO Q, SHI Y T, et al. Compatibilizer in waste tire powder and low-density polyethylene blends and the blends modified asphalt[J].Journal of Applied Polymer Science,2012,123(1):485-492.
 
【9】赖铭,陶国良,俞卫忠,等.聚乙烯/废轮胎胶粉共混体系力学性能的研究[J].中国塑料,2008,22(2):76-80.
 
【10】EL-NEMR K F, KHALIL A M. Gamma irradiation of treated waste rubber powder and its composites with waste polyethylene[J].Journal of Vinyl & Additive Technlogy,2011,17(1):58-63.
 
【11】SONNIER R, LEROY E, CLERC L, et al. Compatibilisation of polyethylene/ground tyre rubber blends by γ irradiation[J].Polymer Degradation and Stability,2006,91(10):2375-2379.
 
【12】SONNIER R, LEROY E, CLERC L, et al. Compatibilizing thermoplastic/ground tyre rubber powder blends: efficiency and limits[J].Polymer Testing,2008,27(7):901-907.
 
【13】赖铭,陶国良,俞卫忠,等.废胶粉填充改性RHDPE增容研究[J].现代塑料加工应用,2008,20(3):31-34.
 
【14】GUO B H, CAO Y, JIA D M, et al. Thermoplastic elastomers derived from scrap rubber powder/LLDPE blend with LLDPE-graft-(epoxidized natural rubber) dual compatibilizer[J].Macromolecular Materials and Engineering,2004,289(4):360-367.
 
【15】罗玲,刘云,余自力.马来酸酐接枝胶粉对胶粉/HDPE共混材料影响的研究[J].塑料工业,2009,37(7):23-25.
 
【16】瓮子良,冯予星,伍社毛,等.废橡胶粉/高密度聚乙烯共混物的界面相容性[J].合成橡胶工业,2007,30(1):39-42.
 
【17】MESZAROS L, BARANY T, CZVIKOVSZKY T. EB-promoted recycling of waste tire rubber with polyolefins[J].Radiation Physics and Chemistry,2012,81(9):1357-1360.
 
【18】LI Y, ZHANG Y, ZHANG Y X. Morphology and mechanical properties of HDPE/SRP/elastomer composites: effect of elastomer polarity[J].Polymer Testing,2004,23(1):83-90.
 
【19】LI Y, ZHANG Y, ZHANG Y X. Structure and mechanical properties of SRP/HDPE/POE(EPR or EPDM) composites[J].Polymer Testing,2003,22(8):859-865.
 
【20】RADHESH K C, FUHRMANN I, KARGER-KOCSIS J. LDPE-based thermoplastic elastomers containing ground tire rubber with and without dynamic curing[J].Polymer Degradation and Stability,2002,76(1):137-144.
 
【21】ABOUZEID M M, RABIE S T, NADA A A, et al. Effect of gamma irradiation on ethylene propylene diene terpolymer rubber composites[J].Nuclear Instruments and Methods in Physics Research: B,2008,266(1):111-116.
 
【22】SHOJAEI A, YOUSEFIAN H, SAHARKHIZ S. Performance characterization of composite materials based on recycled high-density polyethylene and ground tire rubber reinforced with short glass fibers for structural applications[J].Journal of Applied Polymer Science,2007,104(1):1-8.
 
【23】刘晶,揣成智.废胶粉与POE改性二次回收聚丙烯的研究[J].塑料工业,2008,36(11):27-29.
 
【24】LEE S H, BALASUBRAMANIAN M, KIM J K. Dynamic reaction inside co-rotating twin screw extruder. II. waste ground rubber tire powder/polypropylene blends[J].Journal of Applied Polymer Science,2007,106(5):3209-3219.
 
【25】LEE S H, SHANMUGHARAJ A M, SRIDHARC V, et al. Preparation and characterization of polypropylene and waste tire powder modified by allylamine blends[J].Polymers Advanced Technologies,2009,20(7):620-625.
 
【26】LEE S H, ZHANG Z X, XU D, et al. Dynamic reaction involving surface modified waste ground rubber tire powder/polypropylene[J].Polymer Engineering and Science,2009,49(1):168-176.
 
【27】ZHANG S L, XIN Z X, ZHEN Z X, et al. Characterization of the properties of thermoplastic elastomers containing waste rubber tire powder[J].Waste Management,2009,29(5):1480-1485.
 
【28】鄢志兵,张宁,张遂发,等.反应增容聚丙烯/废胶粉共混物的研究[J].现代塑料加工应用,2009,21(3):19-22.
 
【29】MAGIOLI M, SIRQUEIRA A S, SOARES B G. The effect of dynamic vulcanization on the mechanical, dynamic mechanical and fatigue properties of TPV based on polypropylene and ground tire rubber[J].Polymer Testing,2010,29(7):840-848.
 
【30】冯予星, 王益庆, 童亚明, 等. 废胶粉/聚丙烯热塑性弹性体的界面增容研究[J].合成橡胶工业, 2003, 26(1):32-36.
 
【31】GHAISAS S S, KALE D D, KIM J G, et al. Blends of plasticized poly(vinyl chloride) and waste flexible poly(vinyl chloride) with waste nitrile rubber powder[J].Journal of Applied Polymer Science,2004,91(3):1552-1558.
 
【32】冯予星,田明,段先健,等.聚氯乙烯/废胶粉热塑性弹性体的性能研究[J].合成橡胶工业,2002,25(4):235-238.
 
【33】TAN K L, LI C X, MENG H, et al. Preparation and characterization of thermoplastic elastomer of poly(vinyl chloride) and chlorinated waste rubber[J].Polymer Testing,2009,28(1):2-7.
 
【34】李岩,张勇,张隐西.等离子体改性废橡胶胶粉及其与PVC共混复合材料的研究[J].高分子材料科学与工程,2005,21(3):239-242.
 
【35】金波,周翠微,陈必凤,等.精细废轮胎胶粉增韧PVC复合材料应用研究[J].现代塑料加工应用,2004,16(6):18-20.
 
【36】MOU S S, TU M, QIN B H, et al. Rubber crumb toughened polystyrene prepared by reinforcing reaction molding[J].China Synthetic Rubber Industry,2002,25(6):382-382.
 
【37】王浩,张桥,邹头君,等.胶粉改性聚苯乙烯材料的制备与性能[J].武汉工程大学学报,2011,33(7):22-24.
 
【38】KAYNAK C, SIPAHI-SAGLAMA E, AKOVALI G. A fractographic study on toughening of epoxy resin using ground tyre rubber[J].Polymer,2001,42(9):4393-4399.
 
【39】FAN P, LU C H. Grafting of hyperbranched poly (amidoamine) onto waste tire rubber powder and its potential application as the curing agent for epoxy resin[J].Polymers Advanced Technologies,2012,23(1):48-56.
 
【40】游长江,颜正义,曾一铮,等.废胶粉/空心玻璃微珠改性环氧树脂的结构与性能[J].高分子材料科学与工程,2011,27(5):116-119.
 
【41】HASSAN M M, BADWAY N A, GAMAL A M, et al. Studies on mechanical, thermal and morphological properties of irradiated recycled polyamide and waste rubber powder blends[J].Nuclear Instruments and Methods in Physics Research: B, 2010, 268(9):1427-1434.
 
【42】李军伟.废胶粉填充改性ABS复合材料的性能研究[J].上海塑料,2010,151(3):36-38.
 
相关信息
   标题 相关频次
 EOC增韧PLA共混物的制备及性能
 7
 MGF/PLA复合材料的制备及性能
 6
 非生物降解热塑性弹性体在增韧聚乳酸中的应用
 6
 PP-g-MAH改性SGF+POE/FPP复合材料的制备及性能
 4
 咪唑基离子液体增塑聚合物的研究进展
 4
 中空玻璃微珠改性PP泡沫复合材料的发泡效果和力学性能
 4
 紫外光接枝丙烯酸改性废胶粉工艺优化及其复合材料的力学性能
 4
 室温快固型环氧树脂的研究
 3
 1 000 MW核电汽轮机空心螺栓断裂原因分析
 2
 1.25Cr0.5MoSi钢的焊接工艺评定
 2
 1060工业纯铝累积叠轧后的力学性能
 2
 1060铝在累积轧制中组织和性能的演变
 2
 10Ni5CrMoV钢MAG焊接接头的显微组织与力学性能
 2
 12Cr13钢预热处理工艺参数优化
 2
 12Cr1MoV钢过热器爆管的显微组织和力学性能
 2
 14NiCrMo10 6V与Q345E钢过渡匹配焊接接头的组织与力学性能
 2
 15Ni3CrMoV与10Ni5CrMoV异种钢对接接头的显微组织及力学性能
 2
 16Mo3钢大直径大变形量试制中频弯管的组织与性能
 2
 2 000 t水压机立柱断裂分析
 2
 2024铝合金电子束焊接接头的显微组织与力学性能
 2
 20Cr钢与B级钢焊接接头的组织和性能
 2
 2205双相不锈钢/Q345低合金钢爆炸复合板的组织与力学性能
 2
 22Mn2SiVBS热轧无缝钢管控冷时的组织与性能
 2
 240 MPa级高强IF钢的冷轧压下率和退火温度
 2
 25Cr2MoVA钢调质规范对力学性能的影响
 2
 2GPa高压处理对铜铝合金显微组织和性能的影响
 2
 300 MW机组锁口叶片断裂原因分析
 2
 3003铝合金无缝管制备过程中的显微组织与力学性能变化
 2
 3D打印18Ni300模具钢的显微组织及力学性能
 2
 40CrNi2Mo钢的低温力学性能
 2