扫一扫 加微信
首页 > 期刊论文 > 论文摘要
钛及钛合金粉末注射成形的研究进展
          
Research Progress on Powder Injection Molding of Titanium and Titanium Alloy

摘    要
简要介绍了钛及钛合金粉末注射成形技术的特点和优势。从原料粉体、黏结剂体系、注射成形工艺、成形后的性能及微观结构等方面综述了钛及钛合金粉末注射成形的研究进展,提出了未来钛及钛合金粉末注射成形的研究方向。
标    签   钛合金   金属粉末注射成形   titanium   titanium alloy   metal powder injection molding  
 
Abstract
The characteristics and advantages of powder injection molding of titanium and titanium alloys are described in brief. The research progress on powder injection molding of titanium and titanium alloys is reviewed in terms of raw material powder, binder system, injection molding process, performance and microstructure after formation, etc. The research direction in future for powder injection molding of titanium and titanium alloys is also proposed.

中图分类号 TG146.2   DOI 10.11973/jxgccl201806003

 
  中国光学期刊网论文下载说明


所属栏目 综述

基金项目 广东省科学院项目(2016GDASPT-0316;2017GDASCX-0114)

收稿日期 2017/9/5

修改稿日期 2018/5/8

网络出版日期

作者单位点击查看

备注郭鲤(1988-),男,江西吉安人,工程师,硕士

引用该论文: GUO Li,ZHAN Hao,YOU Yuping,YUE Wei. Research Progress on Powder Injection Molding of Titanium and Titanium Alloy[J]. Materials for mechancial engineering, 2018, 42(6): 15~21
郭鲤,詹浩,游玉萍,岳伟. 钛及钛合金粉末注射成形的研究进展[J]. 机械工程材料, 2018, 42(6): 15~21


论文评价
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
分享论文
分享到新浪微博 分享到腾讯微博 分享到人人网 分享到 Google Reader 分享到百度搜藏分享到Twitter

参考文献
【1】肖永清.诠释现代车用钛合金的应用及前景[J]. 铝加工, 2008, 5(1):41-44.
 
【2】CUI C X, HU B M, ZHAO L C, et al. Titanium alloy production technology, market prospects and industry development[J]. Materials and Design, 2011, 32(3):1684-1691.
 
【3】FROES F H. Advances in titanium metal injection molding[J]. Powder Metallurgy and Metal Ceramics, 2007, 46(5/6):303-310.
 
【4】EBEL T. Advances in the metal injection moulding of titanium at Euro PM2014[J]. PIM International, 2015, 9(1):51-61.
 
【5】VIRDHIAN S, OSADA T, KANG H, et al. Evaluation and analysis of distortion of complex shaped Ti-6Al-4V compacts by metal injection molding process[J]. Key Engineering Materials, 2012, 520:187-194.
 
【6】HEANEY D. Handbook of metal injection molding[C]. Cambridge:Woodhead Publishing Limited, 2012, 46(4):203-210.
 
【7】曹家勇. 粉末冶金产业化的重要技术方向[J]. 新材料产业, 2004(11):29-34.
 
【8】FROES F H. Powder injection molding (PIM) of titanium alloys:Ripe for expansion[J]. Materials Technology, 2000, 15(4):295-299.
 
【9】FROES F H, GERMAN R M. Cost reductions prime Ti PIM for growth[J]. Metal Powder Report, 2000, 6(55):12-16.
 
【10】GUO S B, QU X H, HE X B, et al. Mechanical properties and microstructure of Ti-6Al-4V compacts by metal injection molding[J]. Transactions of Nonferrous Metals Society of China, 2004, 14(6):1054-1060.
 
【11】HEIDLOFF A J, RIEKEN J R, ANDERSON I E, et al. Advanced gas atomization processing for Ti and Ti alloy powder manufacturing[J]. JOM, 2010, 62(5):35-41.
 
【12】GERMAN R M. Progress in titanium metal powder injection molding[J]. Materials, 2013, 6(8):3641-3662.
 
【13】EBEL T. Metal injection molding (MIM) of titanium and titanium alloys[M]//Handbook of Metal Injection Molding. Cambridge:Woodhead Publishing Limited, 2012:415-445.
 
【14】KATO K. Effect of sintering temperature on density and tensile properties of titanium compacts by metal injection molding[J]. Journal of the Japan Society of Powder and Power Metallurgy, 2009, 46(8):865-869.
 
【15】刘超, 孔祥吉, 吴胜文,等. 钛及钛合金金属粉末注射成形技术的研究进展[J]. 粉末冶金技术, 2017, 35(2):150-158.
 
【16】CARRENO-MORELLI E, KRSTEVI W, ROMEIRA B, et al. Titanium parts by powder injection moulding of TiH2-based feedstocks[J]. PIM International, 2010, 4(3):60-63.
 
【17】CARRENO-MORELLI E, BIDAUX J E, RODRÍGUEZ-ARBAIZAR M, et al. Production of titanium grade 4 components by powder injection moulding of titanium hydride[J]. Powder Metallurgy, 2014, 57(2):89-92.
 
【18】CARRENO-MORELLI E, RODRÍGUEZ-ARBAIZAR M, AMHERD A, et al. Porous titanium processed by powder injection moulding of titanium hydride and space holders[J]. Powder Metallurgy, 2014, 57(2):93-97.
 
【19】喻岚. 注射成形钛合金的研究[D]. 长沙:中南大学,2004.
 
【20】PARK S J, WU Y, HEANEY D F, et al. Rheological and thermal debinding behaviors in titanium powder injection molding[J]. Metallurgical and Materials Transactions A, 2009, 40(1):215-222.
 
【21】BEAUCHAMP B, RAYMOR A P C. Leading the way with plasma atomised Ti spherical powders for MIM[J]. PIM International, 2011, 5(4):55-57.
 
【22】郭世柏, 曲选辉, 段柏华,等. 注射成形Ti-6Al-4V合金的显微组织和力学性能[J]. 北京科技大学学报, 2005, 27(3):307-311.
 
【23】WEN G, CAO P, GABBITAS B, et al. Development and design of binder systems for titanium metal injection molding:An overview[J]. Metallurgical and Materials Transactions A, 2013, 44(3):1530-1547.
 
【24】GUO S B, DUAN B H, HE X B, et al. Powder injection molding of pure titanium[J]. Rare Metals, 2009, 28(3):261-265.
 
【25】FRIEDERICI V, BRUININK A, IMGRUND P, et al. Getting the powder mix right for design of bone implants[J]. Metal Powder Report, 2010, 65(7):14-16.
 
【26】KRUG S, EVANS J R G, TER MAAT J H H. Transient effects during catalytic binder removal in ceramic injection moulding[J]. Journal of the European Ceramic Society, 2001, 21(12):2275-2283.
 
【27】SIDMBE A T, FIGUEROA I A, HAMILTON H, et al. Metal injection moulding of Ti-64 components using a water soluble binder[J]. PIM International, 2010, 4(4):56-62.
 
【28】SUZUKI K, FUKUSHIMA T. Binder for injection molding of metal powder or ceramic powder and composition and molding method wherein the same is used:US6171360 B1[P]. 2001-01-09.
 
【29】王家惠, 席健, 史庆南. 注射成形钛合金喂料装载量及流变特性研究[J]. 稀有金属材料与工程, 2012, 41(增刊2):827-831.
 
【30】郭世柏, 曲选辉, 段柏华,等. 钛合金粉末注射成形工艺参数的优化[J]. 材料工程, 2004(11):32-36.
 
【31】SUPATI R, LOH N H, KHOR K A, et al. Mixing and characterization of feedstock for powder injection molding[J]. Materials Letters, 2000, 46(2/3):109-114.
 
【32】王家惠. 机械合金化制备纳米晶Ti-6Al-4V及其注射成形工艺研究[D]. 昆明:昆明理工大学, 2014.
 
【33】黄坤祥.金属粉末注射成形[M].台湾:粉末冶金协会,2013.
 
【34】CHEN G, CAO P, WEN G, et al. Debinding behaviour of a water soluble PEG/PMMA binder for Ti metal injection moulding[J]. Materials Chemistry and Physics, 2013, 139(2/3):557-565.
 
【35】GERLING R, AUST E, LIMBERG W, et al. Metal injection moulding of gamma titanium aluminide alloy powder[J]. Materials Science and Engineering:A,2006,423(1/2):262-268.
 
【36】THOMAS Y, BARIL E. Supercritical CO2 debinding:Benefits to titanium powder injection moulding?[C]//World PM2010.[S.l.]:European Powder Metallurgy Association, 2010.
 
【37】刘超, 孔祥吉, 况春江. 生物医用二级纯钛注射成形研究[J]. 粉末冶金技术, 2016, 34(4):281-284.
 
【38】OBASI G C, FERRI O M, EBEL T, et al. Influence of processing parameters on mechanical properties of Ti-6Al-4V alloy fabricated by MIM[J]. Materials Science and Engineering:A, 2010, 527(16/17):3929-3935.
 
【39】NOR N H M, MUHAMAD N, AHMAD S, et al. Sintering parameter optimization of Ti-6Al-4V metal injection molding for highest strength using palm stearin binder[J]. Procedia Engineering, 2013,68:359-364.
 
【40】SIDAMBE A T, FIGUCROA I A, HAMILTON H, et al. Sintering study of CP-Ti and Ti-6Al-4V metal injection moulding parts using Taguchi method[C]//Euro PM2009.[S.l.]:European Powder Metallurgy Association, 2009.
 
【41】ISMAIL M H, GOODALL R, DAVIES H A, et al. Porous NiTi alloy by metal injection moulding/sintering of elemental powders:Effect of sintering temperature[J]. Materials Letters, 2012, 70:142-145.
 
【42】LIMBERG W, EBEL T, PYCZAK F, et al. Influence of the sintering atmosphere on the tensile properties of MIM-processed Ti45Al5Nb0.2B0.2C[J]. Materials Science and Engineering:A, 2012, 552:323-329.
 
【43】CARMAN A, ZHANG L C, IVASISHIN O M, et al. Role of alloying elements in microstructure evolution and alloying elements behaviour during sintering of a near-β titanium alloy[J]. Materials Science and Engineering:A, 2011, 528(3):1686-1693.
 
【44】WEI W, LIU Y, ZHOU K, et al. Effect of Fe addition on sintering behaviour of titanium powder[J]. Powder Metallurgy, 2003, 46(3):246-250.
 
【45】GULSOY H O, GUNAY V, BAYKARA T, et al. Injection molding of mechanical alloyed Ti-Fe-Zr powder[J]. Materials Transactions, 2012, 53(6):1100-1105.
 
【46】LUO S D, YANG Y F, SCHAFFER G B, et al. The effect of a small addition of boron on the sintering densification, microstructure and mechanical properties of powder metallurgy Ti-7Ni alloy[J]. Journal of Alloys and Compounds, 2013, 555:339-346.
 
【47】FERRI O M, EBEL T, BORMANN R. The influence of a small boron addition on the microstructure and mechanical properties of Ti-6Al-4V fabricated by metal injection moulding[J]. Advanced Engineering Materials, 2011, 13(5):436-447.
 
【48】FERRI O M, EBEL T, BORMANN R. Influence of surface quality and porosity on fatigue behaviour of Ti-6Al-4V components processed by MIM[J]. Materials Science and Engineering:A, 2010, 527(7/8):1800-1805.
 
【49】BENSON J M, CHIKWANDA H K. The challenges of titanium metal injection moulding[J]. Journal for New Generation Sciences, 2009, 7(3):1-14.
 
【50】EWART P, JULL H, KVNNEMEYER R, et al. Identification of contamination levels and the microstructure of metal injection moulded titanium[J].Key Engineering Materials, 2016, 704:161-169.
 
【51】UEMATSU T, ITOH Y, SATO K, et al. Effects of substrate for sintering on the mechanical properties of injection molded Ti-6Al-4V alloy[J]. Journal of the Japan Society of Powder and Powder Metallurgy, 2006, 53(9):755-759.
 
【52】ZHAO D, EBEL T, YAN M, et al. Trace carbon in biomedical beta-titanium alloys:Recent progress[J]. JOM, 2015, 67(10):2236-2243.
 
【53】SOYAMA J, OEHRING M, EBEL T, et al. Sintering behavior and microstructure formation of titanium aluminide alloys processed by metal injection molding[J]. JOM, 2017,69(4):676-682.
 
【54】XU W, BRANDT M, SUN S, et al. Additive manufacturing of strong and ductile Ti-6Al-4V by selective laser melting via in situ martensite decomposition[J]. Acta Materialia, 2015, 85:74-84.
 
【55】SIDAMBE A T, FIGUEROA I A, HAMILTON H G C, et al. Metal injection moulding of CP-Ti components for biomedical applications[J]. Journal of Materials Processing Technology, 2012, 212(7):1591-1597.
 
【56】GU Y W, YONG M S, TAY B Y, et al. Synthesis and bioactivity of porous Ti alloy prepared by foaming with TiH2[J]. Materials Science and Engineering:C, 2009, 29(5):1515-1520.
 
【57】TUNCER N, BRAM M, LAPTEV A, et al. Study of metal injection molding of highly porous titanium by physical modeling and direct experiments[J]. Journal of Materials Processing Technology, 2014, 214(7):1352-1360.
 
【58】CHEN L J, LI T, LI Y M, et al. Porous titanium implants fabricated by metal injection molding[J]. Transactions of Nonferrous Metals Society of China,2009,19(5):1174-1179.
 
【59】THIAN E S, LOH N H, KHOR K A, et al. Effects of debinding parameters on powder injection molded Ti-6Al-4V/HA composite parts[J]. Advanced Powder Technology, 2001, 12(3):361-370.
 
【60】AUST E, LIMBERG W, GERLING R, et al. Advanced TiAl6Nb7 bone screw implant fabricated by metal injection moulding[J]. Advanced Engineering Materials, 2006, 8(5):365-370.
 
【61】AROCKIASAMY A, GERMAN R M, HEANEY D F, et al. Effect of additives on sintering response of titanium by powder injection moulding[J]. Powder Metallurgy, 2011, 54(3):420-426.
 
相关信息
   标题 相关频次
 钛及钛合金的缝隙腐蚀行为
 4
 BT20钛合金热变形流变应力的预测模型
 2
 BT22双相钛合金等温锻造工艺的确定
 2
 EBSD测定钛合金中氢化物的取向关系
 2
 EDTA滴定法测定钛合金化铣液和酸洗液中氟的含量
 2
 PCD刀具高速铣削TA15钛合金的切削性能
 2
 SiCf/Ti-6Al-4V复合材料的界面反应及其影响
 2
 TA15钛合金电子束焊缝形貌及显微组织
 2
 TC2钛合金电镀铜的应用
 2
 TC4钛合金齿轮表面渗钼合金化后的组织与性能
 2
 TC4钛合金搅拌摩擦焊温度场的数值模拟
 2
 Ti60/TC17电子束焊接接头的组织及显微硬度
 2
 TiB+TiC+La2O3三元颗粒增强IMI834钛基复合材料的裂纹扩展行为
 2
 表面状态对钛合金铸件荧光渗透检测结果的影响
 2
 超薄TB8钛合金半球成形工艺的有限元模拟
 2
 大厚度钛合金窄间隙TIG焊缝的超声检测
 2
 电感耦合等离子体原子发射光谱法测定磷铁中磷、锰、钛和铝
 2
 电感耦合等离子体原子发射光谱法测定铝质耐火材料中钙、镁、铁、钛及钾的含量
 2
 电感耦合等离子体原子发射光谱法测定钛合金中钯、钇、硼、铌、钽的含量
 2
 电解液pH对钛合金微弧氧化陶瓷膜的影响
 2
 废旧曲轴R角处缺陷的超声波检测
 2
 改进的可见光谱法测定铝合金中钛
 2
 高频感应加热膏剂法制备渗铬层的组织与性能
 2
 高强度钛合金螺栓断裂失效分析
 2
 高强钢与典型管系材料B10和TA2之间的电偶腐蚀及其电绝缘
 2
 高应变速率下两种损伤容限型钛合金的动态压缩变形行为
 2
 锆与钛耐蚀性比较及应用互补性
 2
 光电直读光谱法测定钛合金中13种元素
 2
 光电直读光谱法分析钛合金时铝对碳干扰及校正李海军,陈超选
 2
 航空用钛合金抗微动疲劳表面改性技术的研究进展
 2